Making Progress

Since the last post, we’ve gotten the electrical to the point where we can start insulating. We also had ALK Contracting out to run our gas lines. They are a small local company that specializes in heating, cooling, and plumbing. And while Pete and I ran our internet and cable lines, we hired Aire Care out of Houghton to finish up the job for us. We didn’t have the necessary tools to put the ends on the wires and cables and really we just wanted to make sure we were doing it right. We worked with Roger, who stopped by on a Sunday on his way to camp and showed him what we were working on. He came back out a few days later and finished things up; super nice guy!

We’re installing an oven range vent hood to help with humidity while cooking.  We bought an under cabinet mounted hood that will vent straight out the back.  We located the area where we wanted to the hood to be installed and started making the opening.  We wanted the range hood to be up as high as possible and started hacking into our top plate before going outside to realize that the vent opening would interfere with our soffit.  We relocated the opening so it comes out just below the soffit.  We also had to cut into a stud, so we placed another stud next to it.

As for our gas lines, we had to run three separate lines because we would not have access to the lines in the wall.   When it comes time to install the appliances we’ll have a professional come out to finish the job.  At that time, the tiny house will be out at the property so we’ll have to find another company to finish it up.

And finally, last weekend we put up the netting that came with our wool insulation. We’re scheduled to rent a blower tomorrow morning to blow in the insulation. After that, we’ll be able to put up our vapor barrier and start putting up the tongue and groove cedar.

 

Oven/range hood vent.

Internet/phone and cable access panel.

Gas lines.

Exterior internet/phone and cable connections.

The netting for the insulation was a little staticy.

Just another April snowstorm.

A Productive Vacation

Pete and I had every day last week to work on the tiny house; typically we only work two days every weekend.  While we didn’t accomplish everything we had wanted to, we got a lot of little details taken care of and are that much closer to having the exterior complete.  My mom also spent the week with us and she got busy staining boards and sealing the door when she wasn’t working her own job.

Here is what we managed to accomplish:

We installed the Denver gable trim on the back of the house, but still need to trim it at the top; we installed the soffit boards at the front of the house along with the Denver gable trim; we installed the soffit boards on the dormers; we installed the end wall trim under each of the dormer windows; we installed one 10′ 6″ section of ridge cap over the 12:12 pitched portion of the roof; we framed in the dormer windows, storage loft window, and finished framing the window opposite the porch window (we still need to frame in the porch window but we were waiting for the door to be installed first); we installed sidewall trim on one side of each dormer along with the fascia boards and Denver gable trim; we put up more corner trim in preparation for siding; we stained the porch ceiling; we sided the back of the house; and had the door installed.

We brought the door over to the tiny house for the first time since we picked it up from the door people.  My mom was going to start sealing the door and before she got there we decided to put the door in place and see how it looked.  The company that made our door did a fantastic job; however, they apparently didn’t pay too close attention to our rough opening size because the door/frame was a half-inch taller than our opening and it just barely fit from side to side.  We figured our only option was to sawzall the door header.  We borrowed our friend Eric’s sawzall and Pete went to work taking out an extra inch.  We then proceeded to put the door in place and start leveling it.  After messing around for about half an hour, we decided installing a door was beyond our skill level and had my mom call for help.  She called our long-time family friend John who runs his own carpentry business, JW Ferguson Contracting here in Marquette.  John showed up just before dark as Pete and I were still putting siding up on the back of the house.  We watched John quickly go to work and while he said we could continue doing what we were doing, we wanted to see how a door is supposed to be installed.  We had watched a few YouTube videos, as usual, but quickly admitted defeat.  While we watched John work, we realized we were on the right track to start out, but he knew the order of how to go about screwing and shimming and in no time the door was installed.  When I asked him how much we owed him, he said one hug!  Apparently that’s only his rate for long-time family friends; he has after all known me since I was a baby!  Thanks John for showing up in the evening after a busy day and installing our door!

We had really wanted to get the roof completed this week, but realized we still needed to order a few trim pieces and that would take a week to come in.  We also had to get more trim boards and since we cleaned ProBuild out of their stock of 5/4 cedar we were going to have to wait a few days for that to come in as well.  In another couple of weeks we should be able to declare the exterior complete.

Getting creative while boards dry.

Removing a portion of the header so the door would fit.

The blue painter’s tape will be removed.

Since the Last Post

We’ve been slowly plugging away at the tiny house making small accomplishments almost every weekend.  I’m on annual leave next week and Pete has been laid off early due to the government shutdown so we’re hoping to get the exterior completed on the tiny house.

Since the last post, we’ve continued putting metal up on the roof and as of yesterday, have all the metal sheets installed.  All that’s left for the roof is the ridge cap, end wall trim in front of the dormers, sidewall trim along the sides of the dormers, and the Denver gable trim along the edges of the roof.  We’ve had to stair-step the metal roof panels in places due to things not being perfectly square and we discovered how much harder it is to keep the panels square when you cut a huge section out to go around a skylight.  So the roof is not perfect, but like I probably mentioned in the last post, it will keep the elements outside where they belong.

We installed all the windows in a day and a half.  Putting in the windows has been by far the easiest part of this building project.  We decided that if we have to find new careers, we could be professional window installers.  We did have a close call with one of the windows though.  The instructional video that we watched said to make the windows level horizontally and put a couple nails in.  Then it said to check the level vertically and prior to nailing in around the rest of the window, open the window and make sure it opens as it should.  So we did this on all our windows, sometimes forgetting to open them before nailing on a couple, but we didn’t run into any problems.  On the final window, one of the big ones in the dormer; we did exactly as the instructional video said.  Well, we’re just lucky that I was sitting on scaffolding and not balancing on a ladder!  After putting in our two nails at the bottom and making sure we were level on the sides, Pete started to open the window. When the window was open most of the way, the window proceeded to fall out of the opening!  I was able to stop it from falling all the way out while Pete was pulling it back from the inside so all ended well but it definitely got our hearts beating a little faster.

We also put the trim around most of the windows, got the fascia up along the sides of the house and at the front and back of the house, and put soffits in along the side of the house and at the back of the house.  We also have the fascia installed in front of the dormers because we had to do that before we could put the drip edge on and the rest of the metal panels on the dormer section of the roof.

Our local Menard’s is having a lumber sale, so we took advantage and picked up the bulk of our beveled cedar siding at the lowest price you can buy it in town.  We spent over an hour at the store opening up each package and picking out the best boards.  After going through everything they had in stock, we wound up with forty-one twelve-foot boards.  We’ll probably have to get a few more but this is a good start.

Once we put up all the roof trim pieces, we’ll get the last few windows framed in, finish framing in the corners, and start putting up siding.  We’ve talked my mom into coming and staying with us next week; she’s very good at staining boards! 🙂 Here’s to a productive vacation!

<